Select Page

# The Effect of Gasses on Solar Water Heater

by | Oct 28, 2022 | Physics, Experiments

Contents

## Introduction

In this experiment(The effect of gasses on solar water heater), we will determine whether the time taken by the heating box to heat water at a particular temperature gets affected by changing the gas inside the box.

I hypothesised that the gas that has the lowest thermal conductivity would prove beneficial to the solar heater. The reason is that this gas will stop heat from escaping out from the hot metal plate through the metal valves.

## Aim

To determine the effect of various gasses on solar heating boxes.

## Theory

1. Solar water heating is a process by which water gets heated by sunlight energy with the help of a solar thermal collector.

2. The device which performs this operation is termed a solar water heater.

## Requirements

2. A plastic

3. A glass top

4. An air-tight box

5. Copper pipes

6. Heat plate

7. Water

8. Thermometer

9. Argon

10. Helium

11. Two gas valves

12. 250 Watt heating lamp

13. Notebook

## Procedure

Step 1: Using an airtight box, plastic, copper vines, a heat plate, design a water heater. The heat plate will be fixed below for receiving heat and transferring energy to water.

Step 2: Place water in the solar heater box.

Step 3: Measure the time taken by water that is circulating in the solar water heater to get heat up to 110 degrees Fahrenheit.

Step 4: The regular air in the solar heater box will act as the control.

Step 5: For experimentation, filled the solar heater box with various gasses (Air, Argon and Helium). And repeat the experiment.

Step 6: Perform three tests with each gas.

Step 7: At 70 degrees Fahrenheit, measure the volume of water in each test.

Step 8: Keep the room temperature outside the water at 75 degrees Fahrenheit.

Step 9: On either side of the container, install two valves for placing the gasses (helium and argon) inside the chamber.

Step 10: At a distance of 1.5 feet from the solar water heater place two heating lamps of 259 Watt for keeping the energy constant while it enters the solar heating box.

## Observation

1. We observed that the solar heating ox that was filled with air was more efficient in heating. It took almost 73 minutes.

2. The average time taken by the Argon gas was 76 minutes excluding extraneous results. Including extraneous results, the average time taken was 73 minutes.

3. The average time taken by Helium to heat the water up to 110 degrees Fahrenheit was 84.6 minutes, which was greater than all. Therefore, it was the least efficient.

## Result

1. Our hypothesis proved right with only the helium group, as it took the greater time to heat the water and was the least efficient among all.

2. Argon and air were the most efficient group, contrary to their thermal conductivity.

3. The difference between the efficiency of air and argon lies within a reasonable error margin.

4. Therefore, more precise experiments can only prove or disprove this hypothesis.

## Precaution

1. Take help from someone for welding pipes.

2. Record the observation carefully.

## Conclusion

In this experiment, we determined whether placing different types of gasses inside the chamber of a solar heater box affects its heating capacity.

Q.1 What was the aim of your experiment?

ANS. We aimed to determine the effect of various gasses on the heating capacity of solar water heaters.

Q.2 Which gas showed the most efficiency?

ANS. Argon had the maximum efficiency in heating the water followed by air.

Q.3 Which gas showed the least efficiency?

ANS. Helium had the least efficiency.

## An Analysis of Black Hole Thermodynamics

Introduction In this experiment ( an analysis of blackhole thermodynamics), we will be determining...

## The Most Efficient Automobile Sunshade | Science Experiment

Introduction In this experiment, we will be determining the kind of sunshade material that is the...

## Different Factors Affecting Adhesion In Liquid | Science Experiment

Introduction In this experiment, we will be determining different factors affecting adhesion In...